Advanced Construction And Carpentry Skills by Bonnici 1st Edition – Test Bank

 

To Purchase this Complete Test Bank with Answers Click the link Below

 

https://tbzuiqe.com/product/advanced-construction-and-carpentry-skills-by-bonnici-1st-edition-test-bank/

 

If face any problem or Further information contact us At tbzuiqe@gmail.com

 

 

 

Sample Test

Chapter 03 Testbank

Student: ___________________________________________________________________________

1.   When installing trusses, if you have not thickened or doubled up the top plate you must:
A. not install the trusses until you have done so
B. get the truss engineer to specify new locations for the trusses
C. fit support blocks or extra studs under the trusses that land in between studs
D. relocate all trusses so that they land on existing studs

 

2.   In trussed roof construction ‘live loads’ may impact upon the frame:
A. only during delivery
B. during the standing, assembly and cladding processes
C. only during cladding
D. if there are high winds during assembly

 

3.   Trusses will flex downwards after assembly due to the various loads imposed on them such as cladding, solar panels, roof-mounted air-conditioning or hot water systems. Engineers account for this by building in:
A. extra compression webs
B. camber to the bottom cord
C. thickened top cords
D. strengthened panel points

 

4.   A girder truss is not generally required in:
A. a broken hip and valley roof
B. a hip roof
C. an oblique-ended hipped roof
D. a gable roof

 

5.   When lifting trusses by crane you must always do so by connecting a special plate to the apex of the truss.
True    False

 

6.   Jack trusses are short trusses used to form up the hip end of a roof.
True    False

 

7.   You must remove all temporary frame bracing prior to installing the trussed roof otherwise the loads will not be appropriately distributed.
True    False

 

8.   When a truss is noted to be damaged on site, either from transportation, off-loading, or during storage or installation, you must carefully repair it. This is done using two metal plates not more than 10 mm narrower than the width of the member concerned and twice that in length. These must be through-bolted using a minimum of M10 bolts evenly spaced.
True    False

 

 

 

Chapter 03 Testbank Key

1.   When installing trusses, if you have not thickened or doubled up the top plate you must:
A.not install the trusses until you have done so
B. get the truss engineer to specify new locations for the trusses
C. fit support blocks or extra studs under the trusses that land in between studs
D. relocate all trusses so that they land on existing studs

 

Competency: CPCCCA3006B Erect roof trusses
Difficulty: Easy
Performance criteria: CPCCCA3006B 2.2

2.   In trussed roof construction ‘live loads’ may impact upon the frame:
A.only during delivery
B. during the standing, assembly and cladding processes
C. only during cladding
D. if there are high winds during assembly

 

Competency: CPCCCA3006B Erect roof trusses
Difficulty: Easy
Performance criteria: CPCCCA3006B 1.2

3.   Trusses will flex downwards after assembly due to the various loads imposed on them such as cladding, solar panels, roof-mounted air-conditioning or hot water systems. Engineers account for this by building in:
A.extra compression webs
B. camber to the bottom cord
C. thickened top cords
D. strengthened panel points

 

Competency: CPCCCA3006B Erect roof trusses
Difficulty: Easy
Performance criteria: CPCCCA3006B 1.6

4.   A girder truss is not generally required in:
A.a broken hip and valley roof
B. a hip roof
C. an oblique-ended hipped roof
D. a gable roof

 

Competency: CPCCCA3006B Erect roof trusses
Difficulty: Easy
Performance criteria: CPCCCA3006B 2.1

5.   When lifting trusses by crane you must always do so by connecting a special plate to the apex of the truss.
FALSE

 

Competency: CPCCCA3006B Erect roof trusses
Difficulty: Easy
Performance criteria: CPCCCA3006B 2.3

6.   Jack trusses are short trusses used to form up the hip end of a roof.
TRUE

 

Competency: CPCCCA3006B Erect roof trusses
Difficulty: Easy
Performance criteria: CPCCCA3006B 2.3

7.   You must remove all temporary frame bracing prior to installing the trussed roof otherwise the loads will not be appropriately distributed.
FALSE

 

Competency: CPCCCA3006B Erect roof trusses
Difficulty: Easy
Performance criteria: CPCCCA3006B 1.2

8.   When a truss is noted to be damaged on site, either from transportation, off-loading, or during storage or installation, you must carefully repair it. This is done using two metal plates not more than 10 mm narrower than the width of the member concerned and twice that in length. These must be through-bolted using a minimum of M10 bolts evenly spaced.
FALSE

 

Competency: CPCCCA3006B Erect roof trusses
Difficulty: Easy
Performance criteria: CPCCCA3006B 1.2

 

 

Chapter 03 Testbank Summary

Category	# of Questions
Competency: CPCCCA3006B Erect roof trusses	8
Difficulty: Easy	8
Performance criteria: CPCCCA3006B 1.2	3
Performance criteria: CPCCCA3006B 1.6	1
Performance criteria: CPCCCA3006B 2.1	1
Performance criteria: CPCCCA3006B 2.2	1
Performance criteria: CPCCCA3006B 2.3	2

 

Chapter 05 Testbank

Student: ___________________________________________________________________________

1.   Prior to installing any lining materials the frames must be:
A. fully braced and corners all finish fixed and blocked as required
B. straightened to within 3–5 mm depending upon finish level required
C. fitted out for services such as plumbing, electrical and ducting
D. All the answers are correct.

 

2.   Partially cutting a stud (and appropriately applying side blocking) in order to straighten it is known as:
A. cramping
B. clamping
C. crippling
D. coaching

 

3.   Wall lining materials, such as plasterboard, timber panelling and fibre cement sheet, should always be fixed with a small gap at top and bottom (6–10 mm). The purpose of this gap is:
A. to allow floorboard to expand and not bind against the lining
B. to ensure firm fitting of the skirting against the base of the wall
C. in case there is shrinkage in the frame that could lead to the lining buckling
D. to allow for any upward expansion of the floor due to ground movement

 

4.   Checking the installation of door jambs for ‘wind’ is to:
A. sight by eye from one jamb to the other to check for parallel
B. sight the edge of the jambs to check if they are bowed before installing
C. sight the edge of the jambs to check if they have spring before installing
D. sight the edge of each jamb for straightness as you fix-off

 

5.   Backing off’ a door is designed to ensure the door can close without the edge striking against the opening or lock side jamb.
True    False

 

6.   Scribing is the preferred approach to jointing internal corners for skirting. This is because any gaps that may be produced during installation, or over the life of the building due to movement, are less visible.
True    False

 

7.   To ‘arris’, or ‘arrising’, is the planing or sanding of the faces of materials so as to produce a sharp edge (the arris).
True    False

 

8.   You must always use ‘planted’ (nailed on) door stops on external doors as this allows them to be adjusted over time if the door expands or shrinks with the weather.
True    False

 

 

 

Chapter 05 Testbank Key

1.   Prior to installing any lining materials the frames must be:
A.fully braced and corners all finish fixed and blocked as required
B. straightened to within 3–5 mm depending upon finish level required
C. fitted out for services such as plumbing, electrical and ducting
D. All the answers are correct.

 

Competency: CPCCCA3013A Install lining, panelling and moulding
Difficulty: Easy
Performance criteria: CPCCCA3013A 1.1

2.   Partially cutting a stud (and appropriately applying side blocking) in order to straighten it is known as:
A.cramping
B. clamping
C. crippling
D. coaching

 

Competency: CPCCCA3013A Install lining, panelling and moulding
Difficulty: Easy
Performance criteria: CPCCCA3013A 1.1

3.   Wall lining materials, such as plasterboard, timber panelling and fibre cement sheet, should always be fixed with a small gap at top and bottom (6–10 mm). The purpose of this gap is:
A.to allow floorboard to expand and not bind against the lining
B. to ensure firm fitting of the skirting against the base of the wall
C. in case there is shrinkage in the frame that could lead to the lining buckling
D. to allow for any upward expansion of the floor due to ground movement

 

Competency: CPCCCA3013A Install lining, panelling and moulding
Difficulty: Easy
Performance criteria: CPCCCA3013A 1.1

4.   Checking the installation of door jambs for ‘wind’ is to:
A.sight by eye from one jamb to the other to check for parallel
B. sight the edge of the jambs to check if they are bowed before installing
C. sight the edge of the jambs to check if they have spring before installing
D. sight the edge of each jamb for straightness as you fix-off

 

Competency: CPCCCA3013A Install lining, panelling and moulding
Difficulty: Easy
Performance criteria: CPCCCA3013A 1.2
Performance criteria: CPCCCA3013A 2.2

5.   Backing off’ a door is designed to ensure the door can close without the edge striking against the opening or lock side jamb.
TRUE

 

Competency: CPCCCA3013A Install lining, panelling and moulding
Difficulty: Easy
Performance criteria: CPCCCA3013A 1.2
Performance criteria: CPCCCA3013A 2.2

6.   Scribing is the preferred approach to jointing internal corners for skirting. This is because any gaps that may be produced during installation, or over the life of the building due to movement, are less visible.
TRUE

 

Competency: CPCCCA3013A Install lining, panelling and moulding
Difficulty: Easy
Performance criteria: CPCCCA3013A 4.4

7.   To ‘arris’, or ‘arrising’, is the planing or sanding of the faces of materials so as to produce a sharp edge (the arris).
FALSE

 

Competency: CPCCCA3013A Install lining, panelling and moulding
Difficulty: Easy
Performance criteria: CPCCCA3013A 1.1

8.   You must always use ‘planted’ (nailed on) door stops on external doors as this allows them to be adjusted over time if the door expands or shrinks with the weather.
FALSE

 

Competency: CPCCCA3013A Install lining, panelling and moulding
Difficulty: Easy
Performance criteria: CPCCCA3013A 1.1

 

 

Chapter 05 Testbank Summary

Category	# of Questions
Competency: CPCCCA3013A Install lining, panelling and moulding	8
Difficulty: Easy	8
Performance criteria: CPCCCA3013A 1.1	5
Performance criteria: CPCCCA3013A 1.2	2
Performance criteria: CPCCCA3013A 2.2	2
Performance criteria: CPCCCA3013A 4.4	1